WorldViz User Forum  

Go Back   WorldViz User Forum > Vizard

Reply
 
Thread Tools Rate Thread Display Modes
  #1  
Old 11-21-2016, 03:32 AM
jelly jelly is offline
Member
 
Join Date: Feb 2016
Posts: 38
delaying proximity reaction makes sensor unresponsive for the time of delay

In a recent post I had a problem implementing a delay in the proximity manager and Jeff has suggested the solution of using "vizproximity.waitEnter" and a while loop:

Code:
def proximityTask():
        global handstate
	while True:
		yield vizproximity.waitEnter(SensorIndexFinger)
		print 'entered sensor'
		yield viztask.waitTime(2)
		print 'two seconds elapsed'
                handstate = 1

viztask.schedule(proximityTask())
However, with this code I have a new problem and I decided to open up a new thread:

What happens now is that, once the sensor is entered, the action (change of the variable handstate from 0 to 1), will be delayed by two seconds. However if I happen to enter the sensor again very quickly, before these two 2 seconds have elapsed, nothing happens, as it seems that it is not registered that the sensor has been entered, until the first action takes place.

I wonder if there is a way around this? I tried to to the following: I will change a new variable upon entry but then I will make a new function where I say that IF the new variable "condition" is equal to 1 then after 2 seconds the handstate should change to 1 (= delayed action). This way I am hoping that I am not delaying the action itself in the proximity manager, I am delaying it outside of that function so that the proximity manager can freely register all entries.

Code:
def EnterProximity_IndexFinger(e): # decide what happens on sensor entry
	global handstate, condition
	e.sensor == SensorIndexFinger 
	condition = 1
	print condition
manager.onEnter(SensorIndexFinger,EnterProximity_IndexFinger)
with this I am just changing the variable condition and the I will try to use that in the following way:

Code:
def Handdelay():
	global handstate, condition
	print "now"
	if condition == 1:
		#yield vizproximity.waitEnter(SensorIndexFinger)
		yield viztask.waitTime(2)
		handstate = 1
		print "open hand"
	else:
		handstate = 0

viztask.schedule(Handdelay())
Unfortunately, the condition change is registered as soon as I enter the sensor, but the function which is supposed to call the delayed action (handstate changing to 1) is not working.

I would be very grateful for help!
Reply With Quote
  #2  
Old 11-21-2016, 11:22 AM
Jeff Jeff is offline
WorldViz Team Member
 
Join Date: Aug 2008
Posts: 2,471
It sounds like you need to determine whether the sensor was exited before two seconds elapsed. If that's the case, use the viztask.waitAny command to help with this:

Code:
def proximityTask():
	
	waitEnter = vizproximity.waitEnter(SensorIndexFinger)
	waitExit = vizproximity.waitExit(SensorIndexFinger)
	waitTime = viztask.waitTime(2)
	
	while True:
		yield waitEnter
		print 'entered sensor'
				
		d = yield viztask.waitAny( [ waitExit, waitTime ] )
		
		if d.condition is waitExit:
			print 'Sensor exited before two seconds'
		else: 
			print '2 seconds elapsed'
		
viztask.schedule(proximityTask())
Reply With Quote
  #3  
Old 11-22-2016, 10:02 AM
jelly jelly is offline
Member
 
Join Date: Feb 2016
Posts: 38
I have tried this code but what it does is, it triggers the action as long as the sensor is still entered, after 2 seconds and does not do that if the sensor is exited before 2 seconds have elapsed.

I actually think this might be a different issue:

I want an action to be triggered with a delay, every single time a sensor is entered. If I use waitEnter and waitTime what I achieve is that I "block" the sensor - nothing is registered until the action (and the 2 second delay) are carried out. So it cannot be that I trigger the action EVERY time a sensor is entered, because the 2 second delay creates a minimum of time that needs to have passed before another sensor entry is even registered. Basically, I want the sensor to be entered instantly, each time, and only the action - which is a consequence of the sensor entry - should be triggered with a delay.

Another illustration:

1) If I approach an object, I enter its sensor and I trigger an action of that object.
2) If I want a 2 second delay: I approach an object, I enter its sensor and I trigger an action of that object only after 2 seconds.
3) The problem comes now: If I approach an object a second time within one second of the first time, nothing will happen, because the program is still carrying out the action with delay scheduled as a response to the first approach.
Reply With Quote
  #4  
Old 11-22-2016, 11:07 AM
Jeff Jeff is offline
WorldViz Team Member
 
Join Date: Aug 2008
Posts: 2,471
Try the following example. After the sensor enter event occurs in the proximity task another task is called that handles the delay:

Code:
import viz
import vizproximity
import viztask

viz.go()

dojo = viz.addChild('dojo.osgb')

#Create proximity manager
manager = vizproximity.Manager()
manager.setDebug(viz.ON)

#Add main viewpoint as proximity target
target = vizproximity.Target(viz.MainView)
manager.addTarget(target)

#Create sensor using static matrix
sensor = vizproximity.Sensor(vizproximity.Sphere(1.0),source=viz.Matrix.translate(0,1.5,3))
manager.addSensor(sensor)

def delayTask():
	yield viztask.waitTime(2)
	print '2 seconds elapsed'

def proximityTask():
	while True:
		yield vizproximity.waitEnter(sensor)
		print 'entered sensor'
		viztask.schedule(delayTask())

viztask.schedule(proximityTask())
Reply With Quote
  #5  
Old 11-23-2016, 04:20 AM
jelly jelly is offline
Member
 
Join Date: Feb 2016
Posts: 38
Smile

Jeff, thank you very much! It works perfectly, I have adapted it for my script:

Code:
def delayTask():
	global handstate
	yield viztask.waitTime(2)
	handstate = 1
	print '2 seconds elapsed'
	yield viztask.waitTime(0.7)
	handstate = 0

def proximityTask():
	while True:
		yield vizproximity.waitEnter(SensorIndexFinger)
		print 'entered sensor'
		viztask.schedule(delayTask())

viztask.schedule(proximityTask())
I think I had a good intuition that I needed two steps or two functions to implement this, but I was stuck thinking that I needed the "manager.onEnter". Thanks again!
Reply With Quote
Reply

Tags
proximity, proximity sensor, timing


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Proximity Manager - How to implement delay jelly Vizard 4 11-18-2016 08:48 AM
timer question Elittdogg Vizard 5 10-10-2007 02:49 PM


All times are GMT -7. The time now is 12:27 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Copyright 2002-2023 WorldViz LLC